Please be advised that the site will be down for maintenance on Sunday, September 1, 2024, from 08:00 to 18:00, and again on Monday, September 2, 2024, from 08:00 to 09:00. We apologize for any inconvenience this may cause.
dc.contributor.advisor | Bello-Ochende, Tunde | en |
dc.contributor.coadvisor | Meyer, Josua P. | en |
dc.contributor.postgraduate | Mujanayi Katumba, Jean-Marc | en |
dc.date.accessioned | 2017-07-13T13:28:55Z | |
dc.date.available | 2017-07-13T13:28:55Z | |
dc.date.created | 2017-04-26 | en |
dc.date.issued | 2016 | en |
dc.description | Dissertation (MSc)--University of Pretoria, 2016. | en |
dc.description.abstract | These days, the cooling of new generation electronic servers is a challenge due to the immense heat generated by them. In order to avoid overheating caused by the important rise in temperature appropriate cooling procedures must be used in order to meet the thermal requirement. The current study aims at addressing the issue of overheating in this field, and focuses on the thermal management of electronic devices modelled as a discrete heat sources (mounted in a rectangular cavity) with uniform heat flux applied from the bottom. A review of the literature published regarding the convective heat transfer from heated sources as well as a thorough background on the theory of the cooling of discrete sources by forced convection in rectangular channel is provided in this study. It was showed that the heat transfer performance in channel is strongly influenced by the geometric configurations of heat sources. Therefore, the arrangement and geometric optimisation are the main considerations in the evaluation of thermal performance. Unlike experimental methods that were carried out widely in the past, which provided less cost-effective and more time-consuming means of achieving the same objective, in this study we first explore the possibilities and the advantages of using the CD-adapco's CFD package Star-CCM+ to launch a three dimensional investigation of forced convection heat transfer performance in a channel mounted with equidistant heatgenerating blocks. Numerical results were validated with available experimental data, and showed that the thermal performance of the heat transfer increases with the strength of the flow. The second objective was to maximise the heat transfer density rate to the cooling fluid and to minimise both the average and the maximum temperature in the channel by using the numerical optimisation tool HEEDS/Optimate+. The optimal results showed that better thermal performance was not obtained when the heated sources followed the traditional equidistance arrangement, but was achieved with a specific optimal arrangement under the total length constraint for the first case. Subsequently, for the second case study, on the volume constraints of heat sources, the results proved that optimal configurations that maximise the heat transfer density rate were obtained with a maximum of either the height-to-length ratio or the height-to-width ratio. It was concluded that the heat transfer rate to the cooling fluid increases significantly with the Reynolds number and the optimal results obtained numerically are found to be fairly reliable. | en_ZA |
dc.description.availability | Unrestricted | en |
dc.description.degree | MSc | en |
dc.description.department | Mechanical and Aeronautical Engineering | en |
dc.identifier.citation | Mujanayi Katumba, J 2016, Thermal management and optimisation of heat transfer from discrete heat sources, MSc Dissertation, University of Pretoria, Pretoria, viewed yymmdd <http://hdl.handle.net/2263/61318> | en |
dc.identifier.other | A2017 | en |
dc.identifier.uri | http://hdl.handle.net/2263/61318 | |
dc.language.iso | en | en |
dc.publisher | University of Pretoria | en |
dc.rights | © 2017 University of Pretoria. All rights reserved. The copyright in this work vests in the University of Pretoria. No part of this work may be reproduced or transmitted in any form or by any means, without the prior written permission of the University of Pretoria. | en |
dc.subject | UCTD | en |
dc.subject | Thermal management | en |
dc.subject | Discrete heat sources | en |
dc.subject | Maximise heat transfer | en |
dc.subject | Volume constraints | en |
dc.title | Thermal management and optimisation of heat transfer from discrete heat sources | en_ZA |
dc.type | Dissertation | en |