The experimental flowfield and thermal measurements in an experimental can-type gas turbine combustor

Show simple item record

dc.contributor.advisor Meyer, Josua P. en
dc.contributor.postgraduate Meyers, Bronwyn Clara en
dc.date.accessioned 2013-09-07T11:45:19Z
dc.date.available 2010-08-25 en
dc.date.available 2013-09-07T11:45:19Z
dc.date.created 2010-04-14 en
dc.date.issued 2010-08-25 en
dc.date.submitted 2010-08-25 en
dc.description Dissertation (MEng)--University of Pretoria, 2010. en
dc.description.abstract In this study, experimental data was collected in order to create a test case that can be used to validate computational fluid dynamics (CFD) simulations and the individual models used therein for gas turbine combustor applications. In many cases, the CFD results of gas turbine combustors do not correlate well with experimental results. For this reason, there is a requirement to test the simulation method used before CFD can successfully be used for combustor design. This test case encompasses all the features of a gas turbine combustor such as a swirler, primary, secondary and dilution holes as well as cooling rings. Experiments were performed on the same combustor geometry for both non-reacting and reacting flows. The non-reacting flow experiments consisted of stereoscopic particle image velocimetry (PIV) measurements performed at various planes in the three zones of the combustor. Data was collected on planes, both in line with the holes and in between the holes of each zone. For the reacting experiments, the temperatures on the outlet plane were measured using a thermocouple rake, thus a temperature contour plot on the outlet plane was produced. Further, the combustor can was modified with passive inserts, which were tested to determine their influence on the outlet temperature distribution during reacting runs. In this set-up, the outlet velocity profiles were also measured using a Pitot tube during both non-reacting and reacting flows. In addition to the outlet temperature distribution and velocity profiles, images of the flame patterns were captured, which showed the positions of flame tongues, fluctuating flames and steady flames. Carbon burn patterns on the walls of the combustor liner were also captured. From the data collected during the reacting runs, the pattern factor, profile factor, overall pressure loss and pressure loss factor were calculated. The non-reacting experiments performed using the PIV, produced three-dimensional velocity vector fields throughout the combustor. These experiments were performed at various flow rates, which gave an indication of which features of the combustor flow were affected by the flow rate. When comparing the individual PIV images alongside one another, the temporal nature of the combustor flow was also evident. The reacting experiments revealed a hot region of exhaust gas around the outer edge of the exhaust while there was a cooler region in the centre of the outlet flow. The PIV flowfield results revealed the reason for then hot outer ring-like region was due to the path the hot gasses would take. The hot combustor gas from the primary zone diverges outwards in the secondary zone then is further forced to the outside by the dilution recirculation zone. The hot flow then leaves the combustor along the wall while the cooler air from the jets leaves the combustor in the centre. The experiments performed produced a large variety of data that can be used to validate a number of aspects of combustor simulation using CFD. The non-reacting experimental data can be used to validate the turbulence models used and to evaluate how well the flow features were modelled or captured during the non-reacting stage of the combustor simulation process. The typical flow features such as jet penetration depths and the position and size of the recirculation regions are provided for effective comparison. The thermal results presented on the outlet plane of the combustor can be used for comparison with CFD results once combustion is modelled. Copyright en
dc.description.availability unrestricted en
dc.description.department Mechanical and Aeronautical Engineering en
dc.identifier.citation Meyers, BC 2009, The experimental flowfield and thermal measurements in an experimental can-type gas turbine combustor, MEng dissertation, University of Pretoria, Pretoria, viewed yymmdd < http://hdl.handle.net/2263/27538 > en
dc.identifier.other E10/463/gm en
dc.identifier.upetdurl http://upetd.up.ac.za/thesis/available/etd-08252010-184818/ en
dc.identifier.uri http://hdl.handle.net/2263/27538
dc.language.iso en
dc.publisher University of Pretoria en_ZA
dc.rights © 2009, University of Pretoria. All rights reserved. The copyright in this work vests in the University of Pretoria. No part of this work may be reproduced or transmitted in any form or by any means, without the prior written permission of the University of Pretoria. en
dc.subject Three-dimensional velocity field en
dc.subject Particle image velocimetry en
dc.subject Temperature en
dc.subject Gas turbine combustor en
dc.subject UCTD en_US
dc.title The experimental flowfield and thermal measurements in an experimental can-type gas turbine combustor en
dc.type Dissertation en


Files in this item

This item appears in the following Collection(s)

Show simple item record