Study of sinter reactions when fine iron ore is replaced with coarse ore, using an infrared furnace and sinter pot tests

Show simple item record

dc.contributor.advisor Garbers-Craig, Andrie Mariana en
dc.contributor.postgraduate Nyembwe, Mutombo Alainch en
dc.date.accessioned 2013-09-07T00:51:40Z
dc.date.available 2012-06-26 en
dc.date.available 2013-09-07T00:51:40Z
dc.date.created 2012-04-17 en
dc.date.issued 2012-06-26 en
dc.date.submitted 2012-06-25 en
dc.description Dissertation (MSc)--University of Pretoria, 2012. en
dc.description.abstract The effect of replacing fine ore by coarse ore on sintering reactions was investigated using an infrared furnace on laboratory scale and sinter pots on pilot plant scale. Five sinter mixes were prepared by changing the percentage coarse ore from 0% to 100% in 25% increments. Coarse ore fraction, sintering temperature, holding time and oxygen partial pressure were selected as sintering parameters, and two-level factorial design was used for identification of parameters that significantly influence the formation of sinter phases. Experimental results showed that the coarse ore fraction has a higher effect on the sintering process compared to those of other parameters. The experiment design also enabled to set these parameters to their optimum values. The porosity of compacted pellets was measured using a helium pycnometer. The replacement of fine ore by coarse ore resulted in a decrease in porosity (increase in packing density) of compacted pellets. The particles are closer to each other in pellets consisting of more coarse particles than fine particles. Laboratory experiments were performed at 1300°C in air, using a high heating rate (15°C/s). The holding time was set to 2.5 minutes. X-ray diffraction (XRD), reflected light microscopy (RLM), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) were used to characterize sintering reactions and sinter phases. XRD analysis revealed that sintered pellets consisted of hematite, SFCA, SFCA-I and calcium silicate. The proportions of SFCA slightly increased when the fraction of coarse ore varied from 0% to 25%, but decreased with a further increase in percentage coarse ore. At 25% coarse ore fraction, the porosity of the compacted pellets decreased, resulting in an increase in packing density and sintering rate. More hematite reacted, resulting in the formation of high amounts of SFCA. Above 25% coarse ore fraction, the amount of hematite increased, and the concentrations of columnar SFCA decreased despite a further decrease in porosity. This was attributed to the decrease in reaction surface area for coarse ore, and the short reaction time, which limited the extent of reaction of the coarse particles. The variation of SFCA-I and calcium silicate was not significant under laboratory conditions. Reflected light microscopy and SEM analysis easily identified two major sinter phases: hematite and SFCA. A clear distinction between the different types of SFCA could not be made using EDS analysis. Sinter pot tests were carried out in order to examine the effect of coarse ore fraction on physical and metallurgical properties of sinters. The tumbler and reduction disintegration indexes increased with increasing coarse ore fraction in the sinter bed. This was presumably due to the increase in amounts of hematite and decrease in surface area for reaction. Consequently, the reducibility of sinter decreased as the percentage coarse ore increased. This study has concluded that the presence of 25% coarse ore in the sinter mix led to enhance sintering reactions. The amounts of SFCA increased, and sinter quality was improved. It is recommended that in future work, sintering reactions should further be investigated by also measuring the permeability of the sinter bed and the reaction surface area of solid particles. Copyright en
dc.description.availability unrestricted en
dc.description.department Materials Science and Metallurgical Engineering en
dc.identifier.citation Nyembwe, MA 2011, Study of sinter reactions when fine iron ore is replaced with coarse ore, using an infrared furnace and sinter pot tests, MSc dissertation, University of Pretoria, Pretoria, viewed yymmdd < http://hdl.handle.net/2263/25837 > en
dc.identifier.other E12/4/422/gm en
dc.identifier.upetdurl http://upetd.up.ac.za/thesis/available/etd-06252012-122432/ en
dc.identifier.uri http://hdl.handle.net/2263/25837
dc.language.iso en
dc.publisher University of Pretoria en_ZA
dc.rights © 2011, University of Pretoria. All rights reserved. The copyright in this work vests in the University of Pretoria. No part of this work may be reproduced or transmitted in any form or by any means, without the prior written permission of the University of Pretoria en
dc.subject Coarse ore en
dc.subject Sintering reactions en
dc.subject Xrd analysis en
dc.subject Sfca en
dc.subject Sinter quality en
dc.subject UCTD en_US
dc.title Study of sinter reactions when fine iron ore is replaced with coarse ore, using an infrared furnace and sinter pot tests en
dc.type Dissertation en


Files in this item

This item appears in the following Collection(s)

Show simple item record